Projects

Real jobs, told plainly: where it was, what was wrong, what we did, and how it ended. Where we worked for another fire company, we don't name them or their client — you'll see the job, not the logo.

In short

Real PMP projects, described by building type and area, with the scope of work and how it was delivered. Work done for fire companies and their clients is shown without naming either.

Area: all of Western Australia · Updated

Recent work

Fire water tank replacement, built on site
Fire water tank replacement, built on site
New booster assemblies, tagged and recommissioned
New booster assemblies, tagged and recommissioned
Pump controller and isolator, rewired and commissioned
Pump controller and isolator, rewired and commissioned
Gaseous suppression changeover
Gaseous suppression changeover

Fire pumps

Dual diesel fire pumpset replacement

Residential aged care · Perth inner north

Scope
Replacement of a combined sprinkler and hydrant pump installation: duty and standby diesel pumpsets of 55 kW each, rated at 1,080 L/min at 1,150 kPa, with a new jockey pump and pressure vessel.
Delivery
Factory acceptance testing to AS 2941-2013, then a site load and flow test with a calibrated flow meter through to 130% of the duty point, engine noise readings and a hydrant flow test. Handed over with a Certificate of Compliance and a full operation and maintenance manual.

Fire pumps

Diesel engine replacement on a fire pump

Shopping centre · Perth western suburbs

Scope
The pump's original diesel engine had reached the end of its service life. The pump itself was sound and was kept.
Delivery
New engine installed and the skid modified to suit, with a new heat-exchanger cooling loop and exhaust. An engine management module was fitted so the existing fire pump controller could run a modern electronically governed engine. Commissioned and returned to service.

Control panels

Booster pump controller replacement

High-rise strata · Perth CBD

Scope
Replacement of the domestic water booster controller for a three-pump set (3 × 7.5 kW).
Delivery
A purpose-built variable speed drive controller holding constant pressure across all three pumps, with touchscreen operation and a fault output to the building management system. Installed, wired and commissioned.

Hydrants

Five-yearly hydrant overhauls across a ten-site portfolio

Industrial and logistics · Perth metro

Scope
AS 1851 five-yearly hydrant work across ten industrial and logistics properties, from 20 to more than 40 hydrants per site, alongside the sites' sprinkler valves, diesel, electric and jockey pumps, boosters and tanks.
Delivery
A programmed schedule of one to two days per site, sequenced to keep each property's protection impaired for as short a time as possible.

Maintenance

Routine AS 1851 testing at a major distribution centre

Logistics · Perth metro

Scope
Monthly routine testing across nine sprinkler valve rooms — wet pipe, dry pipe and pre-action — two fire pumpsets and two fire water tanks.
Delivery
Each visit recorded against the site's asset register, with work authority and isolation permits, logbook photographs and call-out records.

Flow testing

Hydrant water supply flow test and report

Residential development · Perth metro

Scope
Flow testing of the feed hydrant to prove the water supply for the site's hydrant system.
Delivery
An engineering report with an extrapolated flow curve, showing 30 L/s available at 290 kPa residual pressure against a 200 kPa requirement.

Sprinklers

Wet pipe sprinkler installation

University campus · Perth

Scope
Installation of a wet pipe sprinkler system.
Delivery
Completed with as-installed drawings, an operation and maintenance manual and a Certificate of Compliance.

Sprinklers

Sprinkler design and installation

Residential aged care · Perth metro

Scope
Design and installation of a sprinkler system using residential sprinkler heads.
Delivery
Designed in-house, installed, and certified with a Certificate of Compliance and handover documentation.

Backflow

Annual backflow testing across three industrial sites

Commercial and industrial · Wangara

Scope
Double check valve assemblies on the fire services of three industrial properties, tested each year under a standing arrangement.
Delivery
Each 150 mm device tested to AS/NZS 2845.3-2020 and the signed test report lodged with the water authority.

Pressure reducing valves

Fire system PRVs reset to the pressure schedule

High-rise office · Perth CBD

Scope
Fire system pressure reducing valves on an upper floor were delivering outside the building's pressure schedule, and a valve on a lower floor was leaking.
Delivery
Valves reset to a 900 kPa downstream setting, associated pressure relief valves adjusted and the leaking valve repaired. The overhaul kit was checked against the valve series before fitting.

Hot water

Hot water compliance upgrade for a commercial tenancy

Commercial tenancy · Perth CBD

Scope
An electric storage hot water unit serving basins needed to be brought up to standard.
Delivery
Pressure reducing valve, cold relief valve, safe tray with tundish waste and a new tempering valve fitted, so outlets deliver no more than 50°C.

Backflow

New backflow device installed and commissioned

Regional fire service · Wheatbelt

Scope
A new 100 mm double check valve assembly required on a fire service.
Delivery
Installed, commissioned and tested on the same day, with the test report lodged.

More projects are added as they are completed. Need a reference for a specific system or building type? Email support@pmpwa.net.au.

What our clients say

We've used PMP Plumbing & Fire Services as our wet fire subcontractor for some time now, and they've become an extension of our own team. Fire pumps, tanks, sprinklers, hydrants and hose reels — servicing, repairs, retrofits and new installations — they handle all of it, and they're there when we need them for after-hours emergency call-outs. Their technicians represent us professionally on our clients' sites, the paperwork comes back the way we need it, and the job gets done right the first time. I'd recommend PMP to any fire protection company that needs a reliable wet fire partner.

Jo PierrotCEO, Protection Engineering

I manage a number of apartment buildings, and when a pressure pump or its controller plays up, the whole building knows about it — fast. PMP Plumbing & Fire Services look after the domestic pumps, controllers and plumbing across the properties I manage, and they've made that side of my job much easier. They attend promptly, explain clearly what's wrong and what it will cost, fix it properly, and send through a clear report I can pass straight on to owners. Reliable, professional and easy to deal with — I'm happy to recommend them to any property manager.

SoniaProperty Manager, Perth real estate agency

As a project and building manager, I need trades I can hand a job to and not have to chase. PMP Plumbing & Fire Services look after both the plumbing and the fire services across the buildings we manage — routine maintenance, breakdowns and project work, from pumps and hot water to sprinklers, hydrants and tanks. They turn up when they say they will, keep me informed, work safely around occupied buildings, and hand over clear reports and paperwork at the end. Having one contractor who covers all of it makes our job much simpler. I'd recommend PMP to any builder or building manager.

Craig DerbyshireDirector, DH Building & Project Solutions

B2M Contracting supplies labour across the Public Transport Authority upgrade works, and we've called on PMP Plumbing & Fire Services for the fire services side many times: boosted flow tests, hydrant flow tests, new hydrant installations and gas suppression commissioning. On a project of this size every contractor has to be organised, and PMP are. Their technicians turn up ready to work, follow the site rules, get the testing done when it's scheduled and hand over clear results and paperwork every time. When we need fire services work done properly and on time, PMP is who we call.

Barry MoranDirector, B2M Contracting Pty Ltd